Ultratec Miniprint 425 Spezifikationen

305–002903USING YOURMINIPRINT 425™

Plugging in power and the telephonelineBe sure to pull the plastic tab out of the battery compartmenton the bottom of the Miniprint 425 before you plu

Charging the batteriesThe AC adapter supplies electricity to the Miniprint 425 andcharges the built-in batteries. Leaving the AC adapter pluggedin wil

About Auto ID™The Auto ID™ feature alerts a hearing person that you arecalling from a TTY. It alerts the person by sending severalaudible tones over t

Setting the print caseThe Miniprint 425 prints everything you type in lowercase(small) letters and everything the other person types inuppercase (CAPI

12 • SETUP

This chapter explains how to make and answer calls in directconnect and with the acoustic cups. It also describes TurboCode and the following advanced

Making a call in direct connect14 • CALLING1. Turn on the Miniprint425.2. Press the dial key(hold down the key and press the key.)3. Type the telephon

Signal light and displayThe signal light and display show what is happening on thetelephone line in the following ways:• Signal light steadily on: dia

Answering a call in direct connect16 • CALLING1. The ring flasher blinkswhen the telephonerings.2. Turn on the Miniprint425.3. Type a greeting andwait

Acoustic calling and answeringCALLING • 171. Put the telephonehandset in the acousticcups on the Miniprint425. Make sure thetelephone cord is on thele

Ultratec, Inc.450 Science DriveMadison, WI 53711(608) 238-5400 (Voice/TTY)Fax: (608) 238-3008Email: [email protected] edition

About Turbo Code®Turbo Code is an enhanced version of Baudot Code. It sendssignals to other Turbo Code TTYs as fast as you can type.TheMiniprint 425 t

INTERRUPT.The other person can choose to stop typing andlet you go ahead or ignore your interruption and continue.If you see INTERRUPT on your display

1. Hold down the and keys and press the key ( + + ) to put the call on hold. Leave the Miniprint425 turned on.2. Go to another TTY connected to the

Transferring a callOffice telephone systems vary widely and specifics of how totransfer a call will be different for each system.Mosttelephone systems

22 • CALLING

Use auto-answer when you want the Miniprint 425 toautomatically answer TTY calls and take messages. One wayto use auto-answer is to turn it on when yo

Turning on auto-answer24 • AUTO-ANSWERPress the auto-answer key(hold down the keyand press the key).4CtrlTurning off auto-answerTo turn off auto-ans

This chapter describes all of the settings you can change withthe options key.They are listed in the order they appear onthe display when you press th

Setting pulse/tone dialingThe Miniprint 425 is set for tone dialing, which is correct foralmost all telephone lines. But you can change to pulsedialin

2. Press the key until you see TURBO CODE ( ON) onthe display.3. Press the to change the setting to OFF.4. Press the key to save the new setting an

CONTENTSImportant safety instructions p. 3Introduction p. 5Overview of the Miniprint 425 6CHAPTER 1 Set-up p. 7Plugging in power and the telephone lin

Setting the Baudot code baud rateEach time you turn on the Miniprint 425, the Baudot codebaud rate is set to the auto setting.The auto setting useswha

Ordinary care of your Miniprint 425 requires changing theprinter paper when it runs out and replacing the batterieswhen they no longer hold a full cha

Replacing the printer paperThe printer uses high-quality thermal paper. Use the ordercard that comes with the Miniprint 425 to order paper. If youdo n

About the batteriesThe Miniprint 425 runs on batteries when you unplug the ACadapter or when the power fails. Fully charged, the 6 AArechargeable NiCa

Replacing the batteriesReplace the batteries every two or three years, or when theyalways run down in less than 30 minutes and exercising themdoes not

TroubleshootingDirect connectDialing does not work.Make sure you have the right tone/pulse setting for yourtelephone system.The display says NO DIRECT

PrinterThe printer does not work.Be sure the printer is on.You can also try resetting the printerby turning the Miniprint 425 off and on.The printer w

Resetting the Miniprint 425Resetting the Miniprint 425 returns all options to theiroriginal settings. Follow these steps to reset the Miniprint425:1.

STICKY KEYSOrdinarily, when you use the or keys, you must holddown either key while you press another key. If you havetrouble pressing two keys at o

SPECIFICATIONSSPECIFICATIONS • 37Physical DimensionsSize: 10" x 9.5" x 3" (25.4 cm x 24.1 cm x 7.6 cm)Weight: 3.75 lbs (1.7 Kg) with ba

Turning off Interrupt 27Setting the Baudot code baud rate 28CHAPTER 5 Care & Repair p. 29Replacing the printer paper 30About the batteries 31Repla

FCC information38 • SPECIFICATIONSThe Miniprint 425 has been tested and found tocomply with the specifications for a Class B digitaldevice pursuant to

SPECIFICATIONS • 39Industry Canada informationNOTICE: This equipment meets the applicableIndustry Canada Terminal Equipment TechnicalSpecifications. T

INDEX40 • INDEXAC adapter, 6, 7, 9, 34jack, 6Acoustic cups, 6 using, 17, 33Adapter, see AC adapter Address, Ultratec, inside front coverAnswering call

Messages, auto-answer, see Auto-answer messagesNO DIRECT CONNECT prompt, 33Options key, 25, 26, 27, 28Paper replacing, 30type needed, 30Phone, see Tel

Conversation EtiquetteGA When you talk with another person by TTY, youtype while the other person reads.When youwant the other person to respond, type

Important safety instructionsWhen using your Miniprint 425, basic safety precautionsshould always be followed to reduce the risk of fire, electricshoc

11.Unplug the Miniprint 425 from the wall outlet and referservicing to qualified service personnel under thefollowing conditions:a. When the power sup

INTRODUCTIONWelcome to the Miniprint 425™TTY from Ultratec.You caneither connect the Miniprint 425 directly to the telephoneline or place any standard

Special keysEscape key quits whatever you are doing and saveschanges.Control key gives instructions to the Miniprint 425 whenyou hold it down and pres

All you need to do to set up the Miniprint 425 is plug it in!You must plug in the AC adapter for 24 hours to charge thebatteries.The ring flasher will